A selection of Mark's enamel work

Notebook

An account of the work as it was made — written at the bench, photographed as it went.

Making a Watch Case

Three bars cut

Making a watch case (part 1)

3 October 2017

I watched the case making videos by Roger Smith on YouTube and followed, in part, the steps that he shows on the vidoes. I'm using brass, though, for…

Mixing some borax

Making a watch case (part 2), soldering the ring joint

3 October 2017

To solder the ring together I'll be using hard solder, hammered into a thin ribbon. This will be drapped over the joint with plenty of borax flux.

Secure the ring in the lathe

Making a watch case (part 3), turning the ring on a lathe

9 October 2017

The ring is placed into a three jaw self-centering chuck. The three jaws automatically move together towards the centre of the chuck so the piece is automatically centred.…

Read all 21 parts →

The Cloisonné Amazon Frog

Engraved Disc Placed Next to Design

Cloisonné Amazon Frog (Part 1)

16 July 2017

This is an experimental project to see if adding a border ring to a domed silver disc improves the overall result of the finished enamel. When I created…

After the second firing of the wires

Cloisonné Amazon Frog (Part 2)

1 August 2017

Here's the starting point for part 2, I've got an engraved disc of the frog and now it's ready to be domed.

Pallet

Cloisonné Amazon Frog (Part 3)

12 September 2017

My pallet tends to grow a bit, here is the state of things after I'm mid-way through the enamelling. It's best not to expand too much, especially for…

Read all 3 parts →

The Enamel Cross

Cross Shape

Enamel Cross Project (part 1)

4 November 2015

I'm currently doing a project to make an alter cross, roughly 14 inches tall and 8 inches wide.

Bottom piece marked out

Enamel Cross Project (part 2)

4 November 2015

This is the second part of my write-up on creating a 14 inch tall enamel cross. The first part can be found here .

Stem and bottom section finished engraving

Enamel Cross Project (part 3)

10 December 2015

Just a quick progress record on the cross project. For part 2 see here .

Read all 10 parts →

Making a Dial

Watch Case with cloisonné frog dial

Making a dial (part 1), making a forming die

7 March 2018

I've got the beginnings of a watch case but, as of yet, no dial that I'm prepared to drill a hole in. I'm not going to put a…

Read all 1 part →

Elliptical Enamel Plaques

Rough Cut Ellipses

Cutting out Elliptical Plaques

3 May 2018

I got a commission to do some paintings onto an elliptical enamel plaque. The major and minor axis of the ellipse are to be 150mm by 90mm, respectively.…

Spray booth setup from the front

Old dishwasher for a spray booth

10 May 2018

To get a good even coating of enamel I've elected to spray wet-process enamel onto the ellipses. Here's my wet backed spray booth... Yes, it's an old dishwasher!

Making A8 sized steel test pieces

15 May 2018

Before I enamel the ellipse I wan't to do some tests. For this I'm cutting out some small rectangles 74mm x 52mm (this is A8 paper size).

Read all 10 parts →

Other writing

The exhibition pieces for the Royal Miniature Painters, Sculptors and Gravers - Annual Exhibition 2019

Three were accepted!

20 November 2019

I got three of these accepted into the Royal Miniature Societies Exhibition this year at the Mall Galleries, London. I can't believe it! I didn't quite manage to…

St. Cecilia and St. Kyneburgha medals next to each other

Gloucester Cathedral Girl Chorister Medals

18 October 2019

Here are the finished pair of chorister medals for the head and deputy head girl choristers at Gloucester Cathedral. The left-hand one depicts St. Cecilia, the patron saint…

St. Kyneburgha initial design

Initial designs for the chorister medals

22 March 2019

After some time the customer and I came up with these designs for the medals. The actual construction of the medals was still a bit unkown at this…

Mark Morris in front of the cabinet displaying his enamel boxes at the RMS exhibition

All five were accepted!

29 November 2018

I got all five entries accepted into the Royal Miniature Society Exhibition! Very pleased indeed! I think I've got to start planning now to do the same for…

The boxes that were displayed at the RMS 2018 exhibition

Royal Society of Miniature Painters, Sculptors and Gravers entries for 2018 exhibition

19 November 2018

Here are my entries for the 2018 Royal Miniature Society exhibition. I've been busy with all manner of different things so I've just not managed to enter anything…

Peridot Green Necklace

Simple Necklaces

20 June 2016

Some time ago I made some colour test strips of the enamel range from Milton Bridge (see Enamel Colour Test blog post). My wife was quite taken with…

Fabergé Style Egg

Fabergé-Style Egg

9 June 2016

I had an interesting enquiry a few weeks ago to make a Fabergé-style egg. Initially the enquiry was about painting some miniatures on the base that would support…

Design to make the cross in sections

Cutting shapes out of 4mm gilding metal

17 February 2016

For the enamel cross project I needed to cut out sections of the cross that could be placed together with a high degree of accuracy. The shapes are…

Painting Saba with a glass of red wine (part 6)

Reproduction of Saba with a Glass of Red Wine by Fabian Perez

20 November 2015

This shows the different stages in painting the reproduction of Saba with a Glass of Wine (original by  by Fabian Perez)   After the first firing, I didn't…

Border Crosses Sampler

Experimental border crosses

30 July 2015

I've been testing out how to create a border of crosses. The idea is to have a band of red enamel with small crosses along the band -…

Entwining Patterns

Entwining Patterns

15 July 2015

I've been experimenting with some champlevé and basse-taille enamelling. This entwining pattern is taken from a medieval enamel religious design. The samples, moving from left to right, respectively…

Workshop Doors from outside

Doors for the workshop

20 February 2015

We had Elite Windows (from Buxton) put in these bi-folding doors in the the workshop. They are really smart.

Snow down our road

Move to Buxton and the New Workshop

2 February 2015

We moved to Buxton in August last year after spending most of the year trying to find a suitable house. As seems to be normal these days, with…

All of the doorknobs together, top down view

Cloisonné Enamel Doorknobs

24 October 2014

I've not had time to update this blog for a while. Here's a picture of a project I completed recently for some cloisonné doorknobs for a handmade kitchen…

Milton Bridge Enamels High Resolution tests

Enamel Colour Tests - High Resolution

7 March 2014

A couple of people have asked me if I could upload a higher resolution picture of the enamel tests than I did in my previous post as the…

Milton Bridge Enamels Test Strips

Enamel Colour Tests

3 March 2014

These are the set of enamel colours that I got from Milton Bridge's British Enamels set. It was quite a lot of work but worth doing. I've got…

The Swindon Advertiser article about Mark Morris' exhibiting at the Heart of the Heat Exhibition 2013

Swindon Advertiser article on the Heart of the Heat Exhibition

17 December 2013

Another good article by Barry Leighton for the Swindon Advertiser. I feel like a celebrity! Here is the online version . Well, there are no more exhibitions planned…

The Heart of the Heat exhibition piece, a Portrait of the Countess Golovine reproduction in miniature

At the Heart of the Heat Exhibition

3 December 2013

This photo of my enamel box is taken at the School of Jewellery, Birmingham UK, where it's on display in the Heart of the Heat Exhibition. I was…

A winter scene just outside my back door

Christmas Orders

27 November 2013

I'm fully booked for Christmas 2013! I can't complain really, but it's not so good for my customers who'd like to find a special gift. It doesn't take…

The Heart of the Heat page for Mark Morris

My Page in the Heart of the Heat Exhibition catalogue

27 November 2013

Here's my page in the Heart of the Heat catalogue, I hope you can read the description.

The Swindon Advertiser article about Mark Morris' exhibiting at the Royal Miniature Society Exhibition

The Fabergé of Freshbrook

1 November 2013

I appeared in Monday's edition of our local paper, the Swindon Advertiser. The journalist referred to me as the Fabergé of Freshbrook (the region of Swindon where I…

Outside the Mall Galleries in London

Enamel Boxes at the Mall Galleries

23 October 2013

Last Wednesday I visited the Mall Galleries where my enamel boxes are on display in the Royal Society of Miniature Painters, Sculptors and Gravers Exhibition. I met up…

Baby Orla miniature enamel portrait, top down view with the box fabric border

Successful Entries for the Royal Society of Miniature Painters Sculptors and Gravers Exhibition

10 October 2013

All five of my entries for the Royal Society's exhibition have been accepted. This is really the best that I could have hoped for. At first I thought…

The Invitation to the Royal Miniature Painters, Sculptors and Gravers - Annual Exhibition 2013

Invitation to the Royal Society of Miniature Painters, Sculptors and Gravers

9 October 2013

Everyone is invited to the Royal Society of Miniature Painters, Sculptors and Gravers. With or without an invitation. I'll be going down on the 16th October.

My entries for the RMS exhibition

Collection of Enamel Box Miniatures for the Royal Society of Miniature Painters Sculptors and Gravers Exhibition

3 October 2013

The collection of miniature enamel paintings that I'm entering for the Royal Society of Miniature Painters Sculptors and Gravers exhibition

Louis Armstrong miniature in enamel, after firing 6 of six

Painting an Enamel Box Lid with a picture of Louis Armstrong

1 October 2013

I use on-glaze enamel paints and mix them with oil and turps substitute to get the right consistency. The turps thins the paint down and the oil acts…

Close up of the lightbox set-up

Photographing Enamel Boxes

23 September 2013

Photographing enamels has always been difficult. The shiny surface makes the light reflections awkward. However I came across some useful tips on Saachti online for photographing artwork in…

Royal Society of Miniature Painters, Sculptors and Gravers Call for Entries

Royal Society of Miniature Painters, Sculptors and Gravers at the Mall Galleries, London

20 September 2013

This one is a big deal, I hope to get 5 pieces accepted! @royalminiature @mallgalleries

no photograph

New links to my website from The Sue Lee Collection & The Hilliard Society of Miniaturists

20 September 2013

The Sue Lee Collection of Miniature Paintings and the Hilliard Society of Miniaturists have kindly put a link to my website from theirs. That was jolly nice of…

Portrait of Countess Golovine - Enamel Miniature Painting by Mark D Morris

Guild of Enamellers and the British Society of Enamellers joint exhibition at the Birmingham School of Jewellery

17 September 2013

I have enterred three pieces into the Guild of Enamellers and the British Society of Enamellers joint exhibition at the Birmingham School of Jewellery. The exhibition is called…

My entries for the Heart of the Heat Exhibition

Entries for the Heart of the Heat Exhibition

22 August 2013

These are the three entries I made for the Guild of Enameller and British Society of Enamellers joint exhition at the School of Jewellery in Birmingham. They are…

By subject